Slicer skills
Meet your infill.
Eleven patterns. A peek inside. A better choice for your next print.
Take a peek inside
Meet the middle.
Infill supports the top of a print and contributes to how it behaves. Start with the part’s job, then compare time, plastic and the finished result. Each pattern below suggests a different PLA product to explore. For a fair pattern comparison, print every test in the same material; matte, silk and glow blends behave differently, and glow needs suitable wear-resistant hardware.
Schematic slices: gyroid and cubic change through height; other diagrams explain the pattern’s structure. Your slicer is the final preview.
Quick prototypes
Rectilinear
A simple starting point for boxes, mockups and everyday prints.
Trade-off & a small test
Directions alternate between layers. Check top-surface support at your chosen density.
Try this: Print a small flat-topped box and inspect the roof.
Try it with this filament
Fast, connected passes
Zigzag / connected lines
Quick prototypes and flat interiors when your slicer offers a connected-line pattern.
Trade-off & a small test
The ends join into a continuous path. It is not the same as a grid with crossings within each layer.
Try this: Compare the travel moves and top support against rectilinear in the preview.
Try it with this filament
Familiar & fast
Grid
A straightforward lattice when the profile already prints it well.
Trade-off & a small test
Lines cross within a layer. Raised crossings can cause nozzle noise or rough infill; rectilinear or gyroid may help.
Try this: Listen for nozzle strikes and compare with rectilinear.
Try it with this filament
Stiff in the layer plane
Triangles
Flat parts where a rigid in-plane lattice suits the load.
Trade-off & a small test
Many intersections and direction changes can increase time and crossing buildup.
Try this: Compare a thin test plate under the actual bending direction.
Try it with this filament
Loads in several directions
Cubic
Functional prototypes where a repeating 3D lattice is useful.
Trade-off & a small test
The pattern changes with height. Walls, orientation and material still determine much of the result.
Try this: Compare identical brackets using the same mass and wall count.
Try it with this filament
Less plastic in open space
Adaptive cubic
Larger parts with spacious interiors and a top surface to support.
Trade-off & a small test
Cells become larger away from surfaces. The drawing shows the density idea; actual cell placement follows model geometry.
Try this: Preview a tall section and check the layers directly below the roof.
Try it with this filament
A flowing 3D structure
Gyroid
A useful all-round choice when load direction varies or a flexible part needs an even internal structure.
Trade-off & a small test
Curves can cost time on some machines. It is not automatically the strongest choice for every part.
Try this: Try a small part in its real load direction before choosing a density.
Try it with this filament
Classic hexagon cells
Honeycomb
A regular cellular interior when its stiffness and appearance fit the project.
Trade-off & a small test
Extra turns can make it slower than simpler patterns. Standard honeycomb is not the same as 3D honeycomb.
Try this: Compare slicer time and material against cubic at the same wall count.
Try it with this filament
Follow the outline
Concentric
Flexible models and shapes where nested contours suit the intended motion.
Trade-off & a small test
Support beneath wide top surfaces depends on geometry; it is not a universal structural pattern.
Try this: Print a small flexible sample and squeeze it in the intended direction.
Try it with this filament
Lightweight display models
Lightning
Decorative parts whose infill mainly needs to support top surfaces.
Trade-off & a small test
The branching interior is intentionally sparse. Do not choose it as a general load-bearing lattice.
Try this: Inspect the support beneath each new top surface in the layer preview.
Try it with this filament
Build toward the roof
Support cubic
Display models needing more support near top surfaces and less lower down.
Trade-off & a small test
Unlike adaptive cubic, density is driven mainly by supporting the roofs rather than filling the whole shape evenly.
Try this: Compare plastic use and roof quality against lightning.
Try it with this filament
Walls first. Then the inside.
For a non-critical PLA prototype, 15–20% infill is a useful experiment, not a strength rating. Check wall count, orientation and top thickness before raising it. Test functional parts under their intended conditions.
Pattern references & illustration notes
These are simplified cutaways, not slicer toolpaths or strength predictions. Adaptive and support cubic show where density is concentrated. Pattern names and availability vary by slicer.
Prusa: infill patterns ↗Prusa: infill settings ↗